fbpx

Tires-Reading a Sidewall

Posted On13.05.2020

Treadwear, Traction, and Temperature Grades

Passengertires Treadweartractiontemp

Uniform Tire Quality Grading

The Uniform Tire Quality Grading System, or UTQG, is a system developed by the government designed to provide consumers with information on tire treadwear, traction, and operating temperature resistance.

Treadwear Rating

The treadwear grade is a comparative numerical rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 200 would wear two times as well on the course as a tire graded 100. The relative performance of a tire depends upon the actual conditions of its use which may depart significantly from the test conditions due to variations in driving habits, service practices, and differences in road characteristics and climates.

Traction Rating

The UTQG Traction Rating indicates the tire’s ability to stop a vehicle moving straight forward on wet pavement. The ratings are AA, A, B, and C, with AA being the best.

Temperature Rating

The UTQG Temperature Rating indicates the tire’s ability to effectively dissipate heat. The ratings range from A to C, with A being the best.

*(UTQG treadwear goes in 20 point increments)

Air Pressure

With the right amount of air pressure, your tires will perform better, wear longer and save fuel. The “right amount” of air pressure for the original equipment or same size tires is specified by the vehicle manufacturer and may be different for front and rear tires. Check with your Nitto dealer if the replacement tires on your vehicle are no longer the same size as the O.E. tires.

U.S DOT Standard Saftey Code

Passengertires US Dot Standard Safety Code

The letters “DOT” certify compliance with all safety standards established by the U.S. Department of Transportation (DOT). This is followed by a combination of up to 12 numbers and letters.

The first two numbers or letters are the plant code where the tire was manufactured, and the last three to four numbers represent the week and year the tire was built.

Tires built in the 1990’s will have three numbers and may have a triangle to note the decade. Examples are below.

Note: Recently it became mandatory to apply a partial DOT serial number on the sidewall opposite the complete DOT serial number. The partial DOT serial does not show the week and year that the tire was manufactured, but may still assist consumers in identifying tires should a recall be necessary. The purpose in applying the partial DOT serial number was to facilitate tire identification when the full DOT serial number may have been mounted towards the inboard side of the vehicle, and consequently not visible unless the vehicle was put on a lift for inspection.

Tire Size, Load Index, and Speed Symbol

Sidewall Passenger

The sidewall of a tire includes a variety of important information. The numbers and letters identify dimensions and performance standards that allow you to compare tires more accurately and efficiently. This diagram will help you to understand those numbers and letters. For assistance in selecting a replacement tire, always consult your Nitto Tire dealer.

Section Width

Sidewall Passenger Heightwidth

The width of a tire is referred to as its section width. This is the width of an inflated tire in millimeters at its widest point from sidewall to sidewall.

Section Height

The section height of the tire is measured in millimeters also. The section height is approximately the distance from the rim to the tread surface of the tire when it is not carrying any weight.

Aspect Ratio

The aspect ratio is the dimensional relationship of the section height to the section width. The lower the aspect ratio, the shorter the sidewall and the wider the shoulder-to-shoulder width.

Radial

The “R” stands for “radial,” indicating the tire has radial construction.

This One is Easy!

Sidewall Passenger Wheeldiameter

The “20” indicates the diameter of the wheel in inches. You can learn more about changing the diameter of the wheels of your car in the Plus Sizing section.

Load Index

Sidewall Passenger Loadindex

The load index number and speed symbol correspond to the maximum load-carrying capacity of the tire and its maximum speed capability.

The load index is an assigned number that corresponds with the load-carrying capacity of the tire. For example, “96” indicates a load-carrying capacity of 1565 lb at maximum inflation pressure. The load index for most passenger car tires ranges from 75-100. Click here to view the complete load inflation index.

Speed Symbol

Sidewall Passenger Speedrating

Speed ratings are determined by indoor laboratory testing methods, which measure high-speed tire durability under controlled test conditions. These test procedures do not take into account underinflation, tire damage, vehicle characteristics or road conditions which can lead to sudden tire failure or loss of vehicle control at much lower speeds than indicated by the tire’s speed rating.

Speed ratings are determined by indoor laboratory testing methods, which measure high-speed tire durability under controlled test conditions. These test procedures do not take into account underinflation, tire damage, vehicle characteristics or road conditions which can lead to sudden tire failure or loss of vehicle control at much lower speeds than indicated by the tire’s speed rating.

Light Truck Tires

Sidewall Lighttruck

The “LT” designation stands for “Light Truck.” These tires are intended for more severe use often seen on trucks and follow load and inflation standards established by the Tire and Rim Association (TRA). Load Index values and load capacities for these tires can be found in TRA manuals.

About Air Pressure

Sidewall Lighttruck Airpressure

With the right amount of air pressure, your tires will perform better, wear longer and save fuel. The “right amount” of air pressure for the original equipment or same size tires is specified by the vehicle manufacturer and may be different for front and rear tires. Check with your Nitto dealer if the replacement tires on your vehicle are no longer the same size as the O.E. tires.

Mud and Snow Designation

Sidewall Lighttruck Mudsnow

The “M+S” indicates the tire is designed for mud and snow applications. The Mud and Snow designation may also appear as “M&S” or “M/S.”

 

Source: Nitto

Send Enquiry
whatsapp